江苏LECO氧氮氢分析仪价格

Software Features & Benefits

Cornerstone brand software is divided into four main sections—Analysis, Diagnostics, Settings, and Instrument—for simplified navigation and organization. Toolbars, sliders, and drop-down menus makeit easy to set parameters for calibration and data processing. The software also includes real-time ambient monitors, with fully animated system diagrams. Advanced diagnostic features include a thorough digital on-board manual, maintenance animations, photo illustrations, and screen captures that quickly provide the direction needed without having to refer to multiple manuals. also Cornerstone supports extended data archiving and flexible reporting capabilities. Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可快速导航和组织。江苏LECO氧氮氢分析仪价格

氧氮氢分析仪

氧氮氢分析仪是一种用于材料科学领域的仪器，于2016年03月09日启用。

技术指标

测量范围： ON 低氧0.0－300ppm OH 低氧0.0－300ppm 高氧0.0－2% 高氧0.0－2% 低氮0.0―300ppm 低氢0.0－50ppm 高氮0.0－2% 高氢0.0－1000ppm 灵敏度： 氧0.01ppm；氮0.1ppm；氢0.01ppm。

主要功能

该仪器配置有16位微处理器和两个**的分别检测高氧和低氧的 红外检测池。氮和氢通过双重范围的热导检测池测量。分析过程中可自动实现从 低范围到高范围的切换。样品在高功率脉冲炉的石墨坩埚中加热可达3000℃以上 高温，脉冲炉采用循环水冷却。该仪器具有灵敏度高、性能好、测量范围宽和分 析结果准确可靠等优点。ONH-2000氧氮氢分析仪是为快速、准确测定铜、钢、铸 铁、合金、钛、镍、钼、锆、陶瓷和其它无机材料中氧、氮、氢的含量而专门设计 制造的。 新疆LECO氧氮氢分析仪采购采用三个**的红外器检测氧含量，同时检测CO和CO2，然后在转化为CO2集中检测。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.

Add approximately 0.05 g of *** Graphite Powder to a 782-720 Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Sample Preparation

Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and

chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.

配置SmartLine® Remote远程诊断功能。

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

改进的红外检测池技术。江苏LECO氧氮氢分析仪价格

氧氮氢分析仪的常见故障及解决方法

供电正常、通讯正常，点击确认键后分析仪不工作。这是没有水流，炉子温度太高或仪器通道电压不正常。如没有水流，炉子温度太高这些信息会显示在显示器画面上，但没有信息显示说明这两项正常。接下来检查仪器通道零位电压，如果比±3V高出1V以上，可能是因为气瓶空了，或者是空气进入到分析仪中。检查并更换化学试剂，如果有空气进入热导池里，热导池的电压就会＜-6V，此时打开右面的门，堵住炉子气体进口，10s后，热导池电压值必然升高。经过逐一排查，**终确认碱石棉有问题，更换后仪器正常。 江苏LECO氧氮氢分析仪价格