浙江氧氮氢分析仪多少钱

ONH836系列：氧氮氢分析仪（熔融法）

软件特点和优势

Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可以快速导航和组织。工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。分析软件同时包括实时的环境参数的监测，提供完整的系统图表模拟。高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。 全自动分析系统、打印机、天平、远程诊断。浙江氧氮氢分析仪多少钱

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of three Standard reps.

Weigh approximately *** grams of a calibration/drift standard into a *** Nickel Capsule; enter the mass and standard identification into appropriate rep fields. If applicable, place the nickel capsule in the appropriate autoloader position.

Note: LECO Reference Materia***o not require preparation. See preparation statement on the reference material certificate. Solid Standards may be used to calibrate when chip or powder standards are not available.

广东元素分析仪供应商可选六轴可旋转触摸屏幕，增强了操作的工效和直观性。

氧氮氢分析仪的使用注意事项：

1 、氧氮氢分析仪在初次启用前，应该对连接点、焊点、阀门等进行检漏，以确保空气中的氧不会反渗进入管道及仪器内部，造成测量数值偏高。

2、再次使用仪器前，要进行管道系统净化，将漏入的空气除干净，同时确保连接取样管路时没有漏入空气。

3、样气中氧含量的变化会受管道材质及表面粗糙度影响，因此一般连接管路选用铜管或抛光过的不锈钢管，而不用塑料管、橡胶管等。

4、微量元素分析时，要避免各种管件、阀门、表头等死角对样气造成污染，因此必须尽可能的简化气路系统，连接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及腊封等设备，才能较好的确保数据的。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.

Add approximately 0.05 g of *** Graphite Powder to a 782-720 Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

长寿命的红外发射光源和无漂移的电路设计保证红外检测池的长期稳定性。

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

Analyze Samples.

Login Sample with the appropriate number of reps.

Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the

appropriate autoloader position.

Repeat steps 3c through 3i for sample analysis.

Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。湖南分析仪优惠价格

力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算。浙江氧氮氢分析仪多少钱

Sample Preparation

Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and

chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.

浙江氧氮氢分析仪多少钱