北京分析仪厂家供应

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

Place the Nickel Capsule containing the sample into the open port at the top of the loading head.

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.

美国LECO力可氧氮氢分析仪ONH836（氧氮氢联测仪）系列硬件部分

特点和优势

1、炉头区域LED照明系统

2、炉头快速拆装的粉尘过滤装置

3、装有自动旁路阀的可快速拆装氧水捕集装置

4、**的动态流量补偿（DFC）保证热导池气体流量、压力恒定

5、改进的红外检测池技术

     新红外池的恒温绝热技术消除了外界环境温度的干扰

   长寿命的红外发射光源和无漂移的电路设计保证红外检测池的长期稳定

   氧高低双量程采用3个碳红外检测器，同时检测一氧化碳和二氧化碳，保证准确定量

  6、高效脉冲炉冷却系统

   强力内循环水冷装置

   双直流风扇保证持续冷却，不受电压波动的影响

   新电极炉头设计，提高脉冲炉热交换效率

  7、全自动分析系统（可选）

   自动清扫装置

   20位或100位全自动分析系统

   高速全自动真空除尘装置直接将粉尘排至仪器外部捕集器中，消除环境污染

安徽氧氮氢分析仪价格用户友好界面的Cornerstone™ 软件。

Method Selection

Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Add approximately 0.05 g of *** Graphite Powder to a***Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen,the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 3b through 3i a minimum of three times for each calibration/drift standard used.

Procedure - Solid Samples

Determine the instrument blank.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of 3 Standard replicates.

Weigh approximately *** grams of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

Note: LECO Reference Materia***o not require preparation.See preparation statement on the reference material certificate.

长寿命的红外发射光源和无漂移的电路设计保证检测器的长期稳定性。新疆专业元素分析仪多少钱

新型气路管道减少气路连接阀，使得漏气，断路故障更少。北京分析仪厂家供应

LECO—Your source for total analytical solutions

CS CS 844 and 744 Series: Carbon/Sulfur by Combustion

Carbon and sulfur determination by combustion infrared detection

Quick, accurate, and affordable determination for both production control and research

Calibration, analysis, evaluation, and diagnostic functions accessible via user-friendly brand software

GDS GDS 500A and 850A Atomic Emission Spectrometers

Spectral range from 120 to 800 nm

Continuous profile of concentration/thickness

Large, dynamic range with concentrations from ppm to 100% by weight

Short analysis time (minutes)

北京分析仪厂家供应