浙江专业分析仪优惠价格

Sample Preparation

Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and

chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.

OHN836系列仪器采用惰性熔融法。浙江专业分析仪优惠价格

氧氮氢分析仪的常见故障及解决方法：

氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。 山东LECO氧氮氢分析仪采购长寿命的红外发射光源和无漂移的电路设计保证检测器的长期稳定性。

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Add approximately 0.05 g of *** Graphite Powder to a***Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen,the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 3b through 3i a minimum of three times for each calibration/drift standard used.

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

ONH836氧氮氢分析仪

高频燃烧红外检测技分析无机材料中的碳、硫含量。

采用惰性气体保护熔融法，提供各种无机材料、钢铁、有色金属、硬质合金、难熔金属、陶瓷等材料中宽范围的氧氮氢同时分析。

该仪器配置MS Windows®的软件接口，专为触摸屏操作定制。长期的开发研究与客户反馈相结合，这个简单方便的软件使得用户可以快速完整访问仪器控制，分析设置，故障诊断，数据报告， **提高日常分析的效率并节省用户宝贵的时间。 可选的Cornerstone® Mobile软件功能，使得用户可以在手机，便携式电脑及台式电脑上便捷的访问仪器数据，分析曲线图形以及仪器的状态，实现对仪器的遥控。

配置SmartLine® Remote远程诊断功能。山东美国LECO分析仪厂家供应

可选六轴可旋转触摸屏幕，增强了操作的工效和直观性。浙江专业分析仪优惠价格

ONH836系列：氧氮氢分析仪（熔融法）

力可ONH836系列仪器采用惰性熔融法，提供各种无机材料、钢铁、有色金属、硬质合金、陶瓷材料中宽范围的氧氮氢同时分析。

ONH836系列仪器通过***采纳客户的反馈意见和创新设计，力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性、降低了分析成本、节省实验室桌面空间。

用户友好界面的Cornerstone™ 软件

力可**的Cornerstone 氧氮氧分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone  氧氮氧分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算，减少了繁琐的额外数据处理。

浙江专业分析仪优惠价格