北京氧氮氢分析仪厂家直销

Instrument Highlights and Features

Features and Benefits

LED light ring illuminates the furnace area

Choice of either argon or helium carrier gas

Novel electrode design increases heat transfer efficiency for increased stability

Non-touch interface systems are also available

User-friendly brand software

High-Performance Detector Design

Thermostatic construction provides increased protection from ambient temperature fluctuations

Optimized emitter control and detection circuitryimproves the IR cell lifetime and long-term stability,

resulting in superior accuracy and precision

Infrared detection for the determination of oxygen, thermoconductivity detection for the determination

of nitrogen

通用下电极坩埚支座，容纳各种坩埚使用。北京氧氮氢分析仪厂家直销

Procedure - Solid Samples

Prepare the instrument as outlined in the operator's instruction manual.

Determine the instrument blank.

Login a minimum of 3 Blank replicates.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open. Place a 502-344 Nickel Basket into the loading head.

Note: samples using automation should be placed in the appropriate autoloader position before starting the

analysis sequence. Once the sequence has started, the automatic analysis will start and end automatically.

Procedure - Solid Samples

Instrument calibration/drift correction.

Place the calibration/drift standard in a *** Nickel Basket, and if applicable, place the sample into the appropriate autoloader position.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

Note: samples using automation should be placed in the appropriate autoloader position before starting the

analysis sequence. Once the sequence has started, the automatic analysis will start and end automatically.

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

配置SmartLine® Remote远程诊断功能。

Determine the instrument blank.

a. Login a minimum of 3 Blank replicates.

b. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

c. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

d. Clean the upper and lower electrode manually, or, if applicable, remove thecrucible and press the analyze button to clean with the automatic cleaner.

e. Firmly place a graphite crucible on the lower electrode tip.

f. Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and endautomatically.

g. Repeat steps 2b through 2f a minimum of three times.

h. Set the blank following the procedure outlined in the operator's instruction manual.

氧氮氢分析仪怎么选？欢迎联系上海禹重科技，我司产品质量保证，欢迎咨询！广东美国LECO分析仪价格

Cornerstone氧氮氧分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。北京氧氮氢分析仪厂家直销

氧氮氢分析仪的常见故障及解决方法

供电正常、通讯正常，点击确认键后分析仪不工作。这是没有水流，炉子温度太高或仪器通道电压不正常。如没有水流，炉子温度太高这些信息会显示在显示器画面上，但没有信息显示说明这两项正常。接下来检查仪器通道零位电压，如果比±3V高出1V以上，可能是因为气瓶空了，或者是空气进入到分析仪中。检查并更换化学试剂，如果有空气进入热导池里，热导池的电压就会＜-6V，此时打开右面的门，堵住炉子气体进口，10s后，热导池电压值必然升高。经过逐一排查，**终确认碱石棉有问题，更换后仪器正常。 北京氧氮氢分析仪厂家直销

上海禹重实业有限公司致力于仪器仪表，是一家服务型公司。公司业务分为光谱仪，色谱仪，质谱仪，样品前处理等，目前不断进行创新和服务改进，为客户提供良好的产品和服务。公司注重以质量为中心，以服务为理念，秉持诚信为本的理念，打造仪器仪表良好品牌。禹重科技秉承“客户为尊、服务为荣、创意为先、技术为实”的经营理念，全力打造公司的重点竞争力。