安徽专业分析仪厂家供应

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

北京美国LECO氧氮氢分析仪采购采用三个**的红外器检测氧含量，同时检测CO和CO2，然后在转化为CO2集中检测。

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

Titanium is a metal that can be combined with elements such as aluminum, vanadium, molybdenum, and tin to produce high-strength, lowdensity, and corrosion-resistant alloys. Titanium alloys are used by the military, medical devices, sporting goods, and aerospace industries because of these properties, and due to the strict demands of these industries, effort needs to be taken to assure that the material meets the highest of quality standards.

Procedure - Solid Samples

Instrument calibration/drift correction.

Add approximately 0.05 g of *** Graphite Powder to a *** Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 3b through 3j a minimum of three times for each calibration/drift standard used.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

力可OHN736&836系列仪器采用惰性熔融法，提供各种无机材料、钢铁、有色金属、硬质合金陶瓷材料中宽范围的氧氮氢同时测定。ONH836仪器通过***采纳客户的反馈意见和创新设计，力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性，降低了分析成本，节省实验室桌面空间。

用户友好界面的Cornerstone™ 软件

力可**的Cornerstone碳硫分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone碳硫分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算。减少了繁琐的额外数据处理。

高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。浙江LECO氧氮氢分析仪厂家直销

**的动态流量补偿（DFC）保证热导池气体流量、压力恒定。安徽专业分析仪厂家供应

氧氮氢分析仪是快速、准确分析氧、氮、氢元素的、高性能仪器，整机采用模块化、一体化设计，即主机由可靠的脉冲电极炉、高灵敏高精度的检测系统、布局合理和气密性好的气路系统、可靠耐用的电源系统、稳定的电路系统、高校节能的水循环散热系统等六个**的硬件模块单元组成。

氧氮氢分析仪的测量原理：

测量范围非常***。分析样品时，样品被称重后放到样品端口中，然后用载气进行冲洗，防止大气（含氧气和氮气）进入到炉子系统中。

石墨坩埚在脉冲炉中脱气，以尽量减少自带的污染。经过稳定阶段后样品落入坩埚中并熔融。样品中的氧与石墨坩埚中的碳反应生成一氧化碳。氮和氢以单质的形式释放。载气和样品气体通过粉尘过滤网后再进入到氧化铜催化炉中，将一氧化碳氧化成二氧化碳。

二氧化碳进入到红外池中用于测定氧含量，被测后的气体导入化学试剂管，这时二氧化碳和水被化学试剂除去，氮元素通过热导检测池含量被测定。测量氢时，载气换为氮气，样品气体通过舒茨试剂而不是氧化铜催化剂。测氧和氮时也可采用更廉价的氩气作为载气。 安徽专业分析仪厂家供应